DIYHD Soft Close Barn Door Hardware Brushed Nickel Rolling Interior Sliding Indoor Track. Hardware Only, Not Including Door Panel. Soft close mechanism were pre-fixed on the track and will be hidden behind the track after installed. Slightly adjust mechanism’s location on the track when install the system. (Make T trigger fully tough the soft close teeth). Soft close kit suitable for wood door weighing up to 170lbs. Do NOT use long track for small door panel. (es, do not use 8ft hardware for 30in door panel, T triggers can not the catch soft close mechanism). Weight Capacity per Door. Pre-fixed on the track. 1 3/8″1 3/4″. Groove Width(Bottom of Door). Groove Height(Bottom of Door). 5ft/5.5ft/6ft/6.6ft are 1 piece track. 8ft is 2pcs 4ft tracks plus 1 track connector. Soft close mechanisms were pre-fixed between first and second holes on each side of the track. The height from top of the door to the top of the roller is 130mm(5 1/8″), please at least 150mm(6″) for installation. Door panel need to be cut a groove for floor guide, Groove Height:1″Width:3/10″. 8FT is 2pcs 4ft tracks with a track connector. The connector is shorter than track, roller can sliding across the connector.

The height from top of the door to the top of the roller is 130mm(5 3/25″), please at least 150mm(6″) for installation. The gap between door and wall is 16mm(16/25″) based on door thickness 40mm(1 4/7″). Door panel need to be cut a groove for floor guide, Groove Height:1″Width:3/10″. Full set hardware including. 5FT(1500mm) track:1pcs. 5FT track is one piece track and pre-drilled 16 apart holes. Can be used for studs wall that length between two studs are 16. 5FT track kit can be used for door width up to 30. The T trigger may not hit with plastic soft close piece we pre-fixed on the track! Easy installation for non wooden frame around openning. If baseboard/wooden frame thickness less than 3/5, easy installation as photo 1 left side. If baseboard/wood frame thickness more than 3/5, please add a thick gasket or wooden board on the back side of the track as photo 2. How to install barn door hardware. How to install barn door hardware: Step1: Drill holes on the wall H is door panel’s height, H+45MM(1.77) is the place we need drill holes for track to tight screws. Step2: Adjust the soft close mechanism’s location to make two teeth visiable from the front side of the track(see step 7 on the photo manuel), then tight the track on the wall Step3: Drill holes on the door panel (see photo manuel step 3) and fix the wheels. Step4: The round dics are anti-pad, they can reduce the gap betweem door and track in case wheels jump off, pls definitely use them(any place on the top of the door and under the track) Step5: Hang wheels on the track. Step6: Install floor guide on the floor under the groove of the door panel Step7: Move two soft close mechanism’s teeth like option 1 Close the door, tight the T trigger on the bottom of the mechanism’s teeth. Open the door, tight the T trigger on the bottom of the mechanism’s teeth. Step8: Mount two stops of the two end of the track. The item “DIYHD Two-Side Soft Closing Mechanism Brushed Nickel Sliding Barn Door Hardware” is in sale since Monday, November 4, 2019. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “beileli_0″ and is located in Carol Stream, Illinois. This item can be shipped to United States.

• Model: TSQ04-Soft Close Kit
• Country/Region of Manufacture: China
• Item Height: 0.25 in
• Item Width: 0.25 in
• Material: Stainless Steel
• Type: Sliding Door Track
• Features: Soft Close
• Color: Silver
• Finish: Brushed
• Item Length: 0.25 in
• Brand: DIYHD
• Suitable For: Wood Door
• Item Diameter: 0.25 in

Two-side soft closing hardware kit. Hardware Material:Steel, Nylon, POM. Two-side soft close mechanisms had been pre-fixed on the track to make full system easy for installation. The soft close mechanism we offered for this item is adjustable which is very thoughtfull. The MAX load for soft close piece is 80kgs. Track had been pre-drilled 16″ apart holes, can be used for 16″ apart studs wall. Two sides of the track’s end also pre-drilled small screw holes for customer who what to creat 10ft double sliding barn door system. A connector can be offered free if you need it! Tips:pls re-move two stops on the middle of the track if you want to creat double door system. Full set hardware’s including. Roller2pcs Stops2pcs 5FT track1pcs Track&wall connector4pcs Soft close kit2 sets Floor guide2pcs Anti-pad2pcs Bolts/Alle key1 set. Big spoke wheel detail. The J shape material is metal. The spoke wheel is hard plastic/nylon. All of our barn door wheel is hard plastic to reduce the noice during sliding. The height from top of the door to the top of the roller is 188mm(7.4), pls check if your wall have enough space to install this kit before order! The gap between door and wall is 16mm(0.63). 5FT track is one piece track and pre-drilled 16 apart holes. Can be used for studs wall that length between two studs are 16. 5FT track kit can be used for door width up to 29 1/2. Easy installation for non wooden frame around openning. If baseboard/wooden frame thickness less than 3/5, easy installation as photo 1 left side. If baseboard/wood frame thickness more than 3/5, please add a thick gasket or wooden board on the back side of the track as photo 2. How to install soft close track system. How to install barn door hardware: Step1: Drill holes on the wall H is door panel’s height, H+45MM(1.77) is the place we need drill holes for track to tight screws. Step2: Adjust the soft close mechanism’s location to make two teeth visiable from the front side of the track(see step 7 on the photo manuel), then tight the track on the wall Step3: Drill holes on the door panel (see photo manuel step 3) and fix the wheels. Step4: The round dics are anti-pad, they can reduce the gap betweem door and track in case wheels jump off, pls definitely use them(any place on the top of the door and under the track) Step5: Hang wheels on the track. Step6: Install floor guide on the floor under the groove of the door panel Step7: Move two soft close mechanism’s teeth like option 1 Close the door, tight the T trigger on the bottom of the mechanism’s teeth. Open the door, tight the T trigger on the bottom of the mechanism’s teeth. Step8: Mount two stops of the two end of the track. The item “Two-Side Close/Soft Open Industrial Wheel Sliding Barn Door Track Hardware Kit” is in sale since Thursday, March 5, 2020. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “sliding-barn-door” and is located in Carol Stream, Illinois. This item can be shipped to United States.

• Country/Region of Manufacture: China
• Material: Stainless Steel
• Brand: DIYHD
• Type: Sliding Door Track

The height from top of the door to the top of the roller is 130mm(5 3/25″), please at least 150mm(6″) for installation. The gap between door and wall is 16mm(16/25″) based on door thickness 40mm(1 4/7″). Door panel need to be cut a groove for floor guide, Groove Height:1″Width:3/10″. 5FT/5.5FT Full set hardware including. 5FT(150m)/5.5FT(1.7m) track:1pcs. 6FT/6.6FT Soft Close Kit Including. Not including other hardware. 5FT track is one piece track and pre-drilled 16 apart holes. Can be used for studs wall that length between two studs are 16. 5FT track kit can be used for door width up to 30. The T trigger may not hit with plastic soft close piece we pre-fixed on the track! Easy installation for non wooden frame around openning. If baseboard/wooden frame thickness less than 3/5, easy installation as photo 1 left side. If baseboard/wood frame thickness more than 3/5, please add a thick gasket or wooden board on the back side of the track as photo 2. How to install barn door hardware. How to install barn door hardware: Step1: Drill holes on the wall H is door panel’s height, H+45MM(1.77) is the place we need drill holes for track to tight screws. Step2: Adjust the soft close mechanism’s location to make two teeth visiable from the front side of the track(see step 7 on the photo manuel), then tight the track on the wall Step3: Drill holes on the door panel (see photo manuel step 3) and fix the wheels. Step4: The round dics are anti-pad, they can reduce the gap betweem door and track in case wheels jump off, pls definitely use them(any place on the top of the door and under the track) Step5: Hang wheels on the track. Step6: Install floor guide on the floor under the groove of the door panel Step7: Move two soft close mechanism’s teeth like option 1 Close the door, tight the T trigger on the bottom of the mechanism’s teeth. Open the door, tight the T trigger on the bottom of the mechanism’s teeth. Step8: Mount two stops of the two end of the track. The item “DIYHD Brushed Nickel Sliding Barn Door Hardware Two-Side Soft Closing Mechanism” is in sale since Monday, October 8, 2018. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “shengyinhardware” and is located in Carol Stream,IL. This item can be shipped to United States.

• Country/Region of Manufacture: China
• Material: STEEL
• Type: Sliding Door Track
• Brand: DIYHD

DIYHD 8FT Soft Closing Brushed Nickel Sliding Barn Door Hardware Two-side soft closing mechanism. Hardware Only, Not including door panel. Material:Steel, Nylon, POM;Surface:Brushed Nickel. Two side soft close operation;The track had been pre-drilled 16” apart holes;Track’s two end had been pre-drilled small holes for track connector to make a long track. Package’s including:Wheel2, Stopper2, Track1, Track&wall connector6, Floor guide1, Anti-pad2;Soft close kit2. Suitable for door thickness:35-40-45mm;Soft close kit can bear MAX weight 80kg. 7.87 x 98.43 x 3.94 inches. The item “DIYHD 8FT Soft Closing Brushed Nickel Sliding Barn Door Hardware Two-side soft” is in sale since Thursday, February 15, 2018. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “trustedkiwi” and is located in US. This item can be shipped to United States.

• Brand: DIYHD
• MPN: BN04-8FT Soft
• Model: BN04-8FT Soft

The height from top of the door to the top of the roller is 130mm(5 3/25″), please at least 150mm(6″) for installation. The gap between door and wall is 16mm(16/25″) based on door thickness 40mm(1 4/7″). Door panel need to be cut a groove for floor guide, Groove Height:1″Width:3/10″. 5FT/5.5FT Full set hardware including. 5FT(150m)/5.5FT(1.7m) track:1pcs. 6FT/6.6FT Soft Close Kit Including. Not including other hardware. 5FT track is one piece track and pre-drilled 16 apart holes. Can be used for studs wall that length between two studs are 16. 5FT track kit can be used for door width up to 30. The T trigger may not hit with plastic soft close piece we pre-fixed on the track! Easy installation for non wooden frame around openning. If baseboard/wooden frame thickness less than 3/5, easy installation as photo 1 left side. If baseboard/wood frame thickness more than 3/5, please add a thick gasket or wooden board on the back side of the track as photo 2. How to install barn door hardware. How to install barn door hardware: Step1: Drill holes on the wall H is door panel’s height, H+45MM(1.77) is the place we need drill holes for track to tight screws. Step2: Adjust the soft close mechanism’s location to make two teeth visiable from the front side of the track(see step 7 on the photo manuel), then tight the track on the wall Step3: Drill holes on the door panel (see photo manuel step 3) and fix the wheels. Step4: The round dics are anti-pad, they can reduce the gap betweem door and track in case wheels jump off, pls definitely use them(any place on the top of the door and under the track) Step5: Hang wheels on the track. Step6: Install floor guide on the floor under the groove of the door panel Step7: Move two soft close mechanism’s teeth like option 1 Close the door, tight the T trigger on the bottom of the mechanism’s teeth. Open the door, tight the T trigger on the bottom of the mechanism’s teeth. Step8: Mount two stops of the two end of the track. The item “DIYHD Brushed Nickel Sliding Barn Door Hardware Two-Side Soft Closing Mechanism” is in sale since Monday, October 8, 2018. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “sliding-barn-door” and is located in Carol Stream,IL. This item can be shipped to United States.

• Material: STEEL
• Brand: DIYHD
• Type: Sliding Door Track
• Country/Region of Manufacture: China

Only hardware for sale, Door is not included. Soft close/Soft open two side soft operation Material:Steel, POM Surface:Brushed Nickel Track’s length should be twice of your door panel’s width Suitable for door panel thickness:35-40-45mm. Soft close kit can bear per door MAX weight:90kgs. The height from top of the door to the top of the roller is 130mm, pls leave at least 150mm for installation. The track’s one end have been pre-drilled holes(using a tracking connector to make two track to be a longer one). The track has been pre-drilled 16 apart holes. Single door kit: 6.6FT single door kit including: Roller:2pcs Stopper:2pcs Sliding track:1pcs6.6FT Track&wall connector+screws:5pcs Anti-jump pad:2pcs Floor guide:1pcs Soft close kit:2 sets. Pre-drilled 16 apart center holes on the track. The item “6.6ft Brushed Nickel Two-Side Soft Closing Sliding Barn Wood Door Hardware Kit” is in sale since Friday, July 15, 2016. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “shengyinhardware” and is located in Carol Stream,IL. This item can be shipped to United States.

• Brand: DIYHD
• MPN: 04BN6.6fts
• Country//Region of Manufacture: China