Sliding Barn Door Hardware Closet Track Kit T Shaped Sliding Door Hardware Set. Transform your dining room with complete sliding barn door kit. With bearings and nylon wheel combination roller, this kit comes with everything you need to upgrade your space. The included graphic & text installation parsing manual makes for easy DIY installation, perfect for family projects. Experience the charm of a sliding barn door without the hassle. Track size: about 58 inches (147CM). Track splicing method: 2 pieces. Scope of application: Door panel thickness 0.5-50MM. 4x roller swivel stand. 2x ground guide fixings. 3x pipe clamp 35mm. 3x wood screws M890. The door is not included. Due to different lighting and screen settings, the item color may be slightly different from the picture. Due to different manual measurements, please allow a 1-2cm difference in size. An unpaid case will be filled after 4 days.

W E L C O M E. 6.6 Feet Bypass Sliding Barn Door Hardware Kit – for Double Wooden Doors-Single Track – Smoothly & Quietly – Easy to Install-Fit 67 Opening. WHY CHOOSE US? Our rail is made by 1/4 heavy duty carbon steel, solid inside, frosted black surface. The rail comes in two pieces, instead of mutiple small pieces, the door can roll quietly and smoothly. OVERLAP SPACE? There would be a 8″-12″ overlap space since the 2 doors are hanging on one single rail. The door panel width should be wider than half of the (opening+overlap sapce) or the opening may not be fully covered. EASY TO INSTALL? Professional instruction and customer service team help you solve all installation problems in time. Save the cost of finding a Carpenter or decoration team. PACKAGE INCLUDED? The picture shows the actual hardware you will receive. DOOR NOT INCLUDED?? HEADBOARD NOT INCLUDED? And we provide you with an accurate list in the Installation instruction. DOOR WEIGHT CAPACITY? Door Weight Limited 220lbs. Fit door panel thickness: 1 3/8″ to 1 3/4″. Q: How to ensure the stability and safety of the door? Two door stoppers slide along the rail and tighten down at any point to stop your door exactly where you want, and they’re cushioned by rubber caps for a quiet close. A T-shaped floor guide is supplied (with anchors) to prevent the door from swinging out or up against the baseboard. Q: When do you need a headboard? If the studs don’t line up with the pre-drilled holes in the rail. If there is a doorway trim. Q: How much space do I need above the doorway? A: You will need a minimum of 6 from the top of your door to the ceiling (or crown molding, if any) for this kit to fit correctly. Q: How thick of a door will this kit work with? A: There are solutions for any thickness of door! The bolts included for attaching the hangers to the door support a thickness range of 1 3/8″ to 1 3/4″, but this can be easily navigated by countersinking the bolt head into the back side of the door, or by picking up 4 longer bolts from your local hardware store. The other thing affected by a thicker door is the spacing needed between the door and wall (or baseboard/doorway trim). Plug in your door depth and trim depth below. 2”- door depth – trim depth. If your answer is 0 or greater, then you’re fine. If your answer was negative, then that number is the extra spacing you need. This extra spacing is accomplished by bolting a header board to the studs, and then the rail to this header board. 4.7 out of 5 stars. 4.6 out of 5 stars. 4.5 out of 5 stars. 1 3/8″ to 1 3/4″. 4.9 out of 5 stars. Door included or not. 4.4 out of 5 stars. 5.0 out of 5 stars. Suitable Track Length (ft). 6.6FT Bypass Kit. 57 x 6.5 x 3 inches. 6.5 inches x 57.0 inches x 3.0 inches. Weight: 22.4 lb. We are always working hard to ensure your package arrives as soon as possible.