100% Satisfaction Satisfaction Guaranteed. 4 FT- 12 FT Bypass Sliding Barn Door Hardware Kit, Single Track, Double Wooden Doors Use, Flat Track Roller, One-Piece Rail Low Ceiling (6FT Single Track Bypass). 73.5 x 6.25 x 3.25 inches. 6.25 inches x 73.5 inches x 3.25 inches. Weight: 19.96 lb. If you have enough 9” ceiling space above door and you prefer the double track bypass, please search ASIN number B06XQFGY2G from our shop. About Single Track Bypass Design? This is single track bypass, one track hang 2 doors, the roller diameter is 2-5/8”, so the door will be have 8”-10” distance door overlap between 2 doors, so each door should be 6” wider than half the width of the opening, and the 2 rollers will be hit together when one door slide, maybe drive another door slide. Single Track Bypass System? Upgraded One-Piece single track bypass sliding barn door hardware is low ceiling design, only need 6 inch ceiling space from top of the door to ceiling; Wall-mounted is very easy to install, no tedious installation steps, no request wall to be twice the width of the opening, suitable for small home space, saves more space than a side pull door and traditional double track bypass kit, can help you finish the project more quickly and easily. Why Choice Bypass Barn Door Hardware Kit? Roller Bearing is high purity bearing steel Gcr15, made of reinforced steel and electrophoretic, ring fixed structure and external dust cover, prevent steel ball from leaving the locus and oil leakage, keep roller lifetime lubricated; Passed the test of opening – closing for 160000 times, wear-resisting, ensure the stability of the move and the wheel’s fluency. One full piece 6ft rail and Pre-drill 16 apart hole on rail to line up standard studs. Heavy duty construction ensures safety? Material thickness up to 1/4 inch (6.3cm) Solid carbon steel (High Standard Q235), multiple high temperature fine electrostatic powder spraying process black frosted, corrosion protection, antirust, anti-scratch. 8.8 grade Self-tapping and roller bolt make our hardware kit can hold total 265 lbs doors comfortably. Door Stopper have rubber covered, good buffer effect, and educe the noise. The hanger wheel surface is covered with nylon, slide very quietly. Single Track Bypass Sliding Barn Door Hardware Package include? 1 x 6FT Rail, 5 x spacers, 4 x Rollers, 2 x Door Stops, 4 x anti-jump pad, 2 x Floor Guides, 1 x Installation Manual (step by step with fractional measurements in inch, very easy to install)–Only bypass barn door hardware for sale, barn door is not include. Fit for 1-3/8″ to 1-3/4″ door panel thickness, can’t more than 1-3/4. S warehouse, any problem in using it, our professional staff in the barn door hardware field will answer questions for you in 24 hours. ZEKOO has devoted to the development of barn door hardware over 10 years, improve and upgrade products to give each family the most appropriate choice. ZEKOO 6ft single track bypass sliding barn door hardware kit use for double doors (door is not include). Q: How to choose barn door track size of single track bypass system? A: Barn door track length = Your opening width +1FT. For example, if your opening is 5FT (60”) wide, you will need 5FT+1FT = 6FT(72”) long track, your each door needs to be 36” wide, your opening will show 31” wide when the door open. Q: Can the single track bypass barn door hardware system let the opening show fully? A: Yes, you can select a longer track, if each door is 36” wide, you can choose 9FT track kit. Q: How confirm door width for the single track bypass system? A: Because this is single track bypass, one track hang 2 doors, the wheel diameter is 2-5/8”, so there are at least have 6” overlap between 2 doors when your install the hanger close to the edge of door, usually it will have 8”-10” overlap, so your each door width = Half width of opening + 5” to 6′. Q: Can each door slide independently on the track? A: No, the 2 doors slide on same track, so the 2 rollers will be hit together when one door slide to the end, maybe drive another door slide, if you have enough ceiling space above door for 9”, you can choice double track bypass system, please search ASIN number B06XPYZV8M from our shop. Q: Can the single track bypass use for four door also? A: Yes, you can add 1 set straight hanger B01KH3OH62 and 1 set offset hanger B08L4FN1ZP for the other 2 doors, please search the product number from our shop, just need to know that there have 8”-10” overlap between 2 doors, so each door need 5”-6” wider. About all accessories of 6 FT single track bypass hardware. 1 piece whole 6ft rail. Pre-drilled 16 apart holes. On track, make by solid 1/4 (6.3mm) thick steel, with 8.8 grade high strengh bearing capacity lag blots, fit for concrete wall and wooden wall. Provide 1-3/8” length spacer, it can control the gap between the door and the wall, if you have the door trim on wall, you can change other length spacer, please tell us. Prevent the door falling off from the track, it installed at the end of track 2 side, ensure the stability and safety, with the rubber plug, good damping effect and reduce the noise, have 2 screws to fasten stopper on track, you can put stopper on track where you want to stop your door, easy to remove if you want adjust. Can prevent the door swinging back and forth or against the baseboard, let your door slide on same locus, fit for all thickness with grooved or ungrooved doors. Can prevent door to be lifted off rail when the barn door slide, ensure the stability and safety. Only the hardware is for sale, door is not included, we are professional factory, accept mass customization. 1The hardware kit is heavy, we suggest to install the track on the studs of the wall. The hardware kit can also be installed on the brick wall and wood wall. If the wall is drywall or sheetrock, and no studs in the wall, the installed track might descend, the kit will not work. 2If there’s thick trim/baseboard/deco on the wall, you may need install the headboard on the wall, then install the track on the headboard. If you can’t sure that if the headboard is needed or not, please let us know, we will assist you. 3The recommended door thickness is from 1-3/8″ to 1-3/4″, because the size of offset hanger is fixed, the door thickness can’t more than 1-3/4. If door is thin, you may need to check the gap info below, to know the gap between door&wall, inside door&outside door. The barn door hanger roller with Professional bearings, make your bypass barn door hardware service life last longer. Material quality is high purity bearing steel Gcr15, professional bearing materials, ring fixed structure bearing, wraps around the steel ball and prevent steel ball from leaving the locus, make sliding more stable. There is a dust cover the bearing to prevent dust from entering and lubricating oil leakage, let the roller can slide smoothly and more durable. 1 hanger with 2 life time lubricated bearing, ensure sliding balance and stability, test beyond 160,000, you can use it for a long time. The roller surface is covered with nylon, wear-resisting and slide very quietly. We design the Dowel pin Front part slightly larger, keep the dowel stuck in hole not fall off. All of prat is make by Q235 carbon steel, thick is 1/4” (6.3mm). 8.8 grade roller bolt can hold the doors comfortably. The offset hanger with anti-jump design, give you safe sliding door experience. Single track bypass hardware kit package include. 1 x 6FT Rail. 2 x Straight steel Hanger with bolt. 2 x Offset steel Hanger with bolt. 2 x Door Stopper with Hex Wrench. 5 x 1-3/8” Spacer with lag bolt. 2 x Floor Guide with screw. 2 x Anti-Jumper with screw. 2 x Offset Anti-Jumper with screw. 1 x Barn Door Hardware Installation Manual. Why choice Single track bypass barn door hardware. Single track bypass barn door hardware system slides horizontally, it can save space compared with ordinary push door. Wall-mounted is low ceiling 6” install, no tedious installation steps, no request wall to be twice the width of the opening, suitable for small home space. Decorate your locker room, closet, kitchen, wardrobe, bathroom, bedroom, storeroom, change your home dull image. Barn door Installation dimension. Q: How much gap of the double track bypass system? A: We suggest door thickness less than or equal to 1-9/16”, If your door thickness is 1-9/16”, the gap between inner door&wall is about 5/8”, the gap between two door panels is about 1-3/16”, the outer door extend from the wall is 5”. Q: How to narrow the gap for the thinner door? A: If the thinner the door, the larger the gap, you can add a headboard on front of door, then install the hanger on headboard, that can narrow the gap of door with wall and door with door. Single track barn door bypass instructions step by step with fractional measurements in inch, have detailed word instructions with pictures. The track drilling hole on wall is = your door height + 1-11/16′. The hanger first hole install on door is 1-9/16″ from top of door, second hole is 3-9/16″ from first hole. Q: How much ceiling space requirement of the single track bypass system? A: At least 6 from top of door to ceiling to install. Q: Can i cut the track? A: Yes, you can cut it into any length of you want. Q: Can i use it for outdoors? A: We suggest if use for outdoors, you can make some cover above the track, and you need paint and add oil regularly to extended service life. Q: What circumstances do I need to add a headboard? If you have a doorway trim; 2. If the studs don’t line up with the pre-drilled holes in the rail. Q: How thick door use for it? What is the weight capacity? We suggest 1-3/8″ 1-9/16″ thick door will be better, If your door thick is 1-1-3/4, the inner door bolts need reverse installation, because the offset hanger size is fixed; 2. We offer the best prices around on high quality products. Our E-store includes media such as books, movies, music and games while offering electronics, toys, sporting apparel, clothing, tools, general home, garden items and more. We are always working hard to ensure your package arrives as soon as possible. We do not accept P. Please provide a physical address. We try over very best to make sure every customer is completely satisfied. If there’s a problem, message us! We’re happy to help. This item is in the category “Home & Garden\Home Improvement\Building & Hardware\Doors & Door Hardware\Other Door Hardware”. The seller is “jankap-11″ and is located in this country: US. This item can be shipped to United States.
- Item model number: GCM5164-1
- Part Number: GCM5164-1
- Style: Classic
- Size: 6 Feet
- Assembly Required: Yes
- Color: Black
- Material: Alloy Steel
- Batteries Required?: No
- Item Weight: 19.96 pounds
- Shape: I shape
- Batteries Included?: No
- Measurement System: English/Standard
- Installation Method: Screw-In
- Package Dimensions: 73.5 x 6.25 x 3.25 inches
- UPC: 726084140561
- EAN: 0726084140561